Cannot write and format in drive B:
Cannot write and format in drive B:
I buy SD HXC Emulator 5 set but only plane PCB and PIC.
I'm mad vfo for PC 9801UV11 It's work fine.
I can read and write on 1 MB floppy image and 720 kB MFM but transfer rate is 300 kBit/s only.
ok can accept until I'm select drive B: to operate both of capacity(1MB ,720kB) can not format and write in drive B:
It can fine directory but cannot format and write.On LCD in WETO message up.
I'm mad vfo for PC 9801UV11 It's work fine.
I can read and write on 1 MB floppy image and 720 kB MFM but transfer rate is 300 kBit/s only.
ok can accept until I'm select drive B: to operate both of capacity(1MB ,720kB) can not format and write in drive B:
It can fine directory but cannot format and write.On LCD in WETO message up.
Re: Cannot write and format in drive B:
Do you have the last firmware ? (v1.7.1.2)sixty_cel wrote:I buy SD HXC Emulator 5 set but only plane PCB and PIC.
I'm mad vfo for PC 9801UV11 It's work fine.
I can read and write on 1 MB floppy image and 720 kB MFM but transfer rate is 300 kBit/s only.
ok can accept until I'm select drive B: to operate both of capacity(1MB ,720kB) can not format and write in drive B:
It can fine directory but cannot format and write.On LCD in WETO message up.
Re: Cannot write and format in drive B:
sixty_cel wrote:
I buy SD HXC Emulator 5 set but only plane PCB and PIC.
I'm mad vfo for PC 9801UV11 It's work fine.
I can read and write on 1 MB floppy image and 720 kB MFM but transfer rate is 300 kBit/s only.
ok can accept until I'm select drive B: to operate both of capacity(1MB ,720kB) can not format and write in drive B:
It can fine directory but cannot format and write.On LCD in WETO message up.
Do you have the last firmware ? (v1.7.1.2)
OK jeff Thank you your reply
After I'm upgrade firmware to ver 1.7.1.2
Now all of Drive A: and B: cannot format.
I buy SD HXC Emulator 5 set but only plane PCB and PIC.
I'm mad vfo for PC 9801UV11 It's work fine.
I can read and write on 1 MB floppy image and 720 kB MFM but transfer rate is 300 kBit/s only.
ok can accept until I'm select drive B: to operate both of capacity(1MB ,720kB) can not format and write in drive B:
It can fine directory but cannot format and write.On LCD in WETO message up.
Do you have the last firmware ? (v1.7.1.2)
OK jeff Thank you your reply
After I'm upgrade firmware to ver 1.7.1.2
Now all of Drive A: and B: cannot format.
Re: Cannot write and format in drive B:
Before upgrade It's v 1.6.0.0
I'm can operate in dos mode with command
-ren -copy -del or etc
After upgrade It's v 1.7.1.2
Cannot do anything It's not operate with command upper.
I'm can operate in dos mode with command
-ren -copy -del or etc
After upgrade It's v 1.7.1.2
Cannot do anything It's not operate with command upper.
Re: Cannot write and format in drive B:
Please show me the jumpers setting.
Re: Cannot write and format in drive B:
in picture
I'm set drive B:(I'm call second drive) is boot drive and in PC see It's drive A:
and set drive A:(I'm call first drive)is drive B:in PC.
Then after boot I'm goto format program if I run this program from second drive I can format fine first drive in v 1.6.0.0
but can not format both A: and B: in v 1.7.1.2
That mean first drive can format and second drive cannot format in v 1.6.0.0
second time for update the image sometime can format first drive.
I'm set drive B:(I'm call second drive) is boot drive and in PC see It's drive A:
and set drive A:(I'm call first drive)is drive B:in PC.
Then after boot I'm goto format program if I run this program from second drive I can format fine first drive in v 1.6.0.0
but can not format both A: and B: in v 1.7.1.2
That mean first drive can format and second drive cannot format in v 1.6.0.0
second time for update the image sometime can format first drive.
- Attachments
-
- DSCN9528.jpg (96.92 KiB) Viewed 9580 times
Last edited by sixty_cel on Mon Jul 16, 2012 4:08 pm, edited 1 time in total.
Re: Cannot write and format in drive B:
in this picture
It's my first process I'm boot program in drive A:
and cannot format drive B:(v1.6.0.0)
It's my first process I'm boot program in drive A:
and cannot format drive B:(v1.6.0.0)
- Attachments
-
- DSCN9530.jpg (110.07 KiB) Viewed 9580 times
Re: Cannot write and format in drive B:
ok in v1.7.1.2 can format in same capacity but cannot format in differrent capacity of both drive.
Re: Cannot write and format in drive B:
So you can write files on A: & B: ?sixty_cel wrote:ok in v1.7.1.2 can format in same capacity but cannot format in differrent capacity of both drive.
Re: Cannot write and format in drive B:
Hi Jeff
Sorry for my mistake all problem from my sdcard the write protech switch was broken.
Now every thing work fine.
But some problem about vfdwin cannot open some image file 1MB.
It can open 720k but cannot open 1MB.
Sorry for my mistake all problem from my sdcard the write protech switch was broken.
Now every thing work fine.
But some problem about vfdwin cannot open some image file 1MB.
It can open 720k but cannot open 1MB.
Re: Cannot write and format in drive B:
a file image please ?sixty_cel wrote:Hi Jeff
Sorry for my mistake all problem from my sdcard the write protech switch was broken.
Now every thing work fine.
But some problem about vfdwin cannot open some image file 1MB.
It can open 720k but cannot open 1MB.
Re: Cannot write and format in drive B:
this is an image file of 1MB
I'm cannot attach file here
On HxCFloppyEmulator V1.6.11.15 tab Load Raw image
I'm set Track type =MFM
Two sides floppy
Auto GAP3
Number of track =77 , Sector per track=8
Sector ID start =1 , RPM =360
Sectors size =1024 , Bitrate =500000
Format value =246 , Interleave =1 , Skew =0 Total sector =1232 , Total size 1261568
That's all
Then click tab "Creat Empty Floppy"
Back to windows "HxCFloppyEmulator V1.6.11.15"
Click tab"Export" then export to my sdcard and format again with Japanese dos.
After format can operate on PC 98..xx series but cannot open with vfdwin.
The error occor send Error Report or Don't Send
I'm cannot attach file here
On HxCFloppyEmulator V1.6.11.15 tab Load Raw image
I'm set Track type =MFM
Two sides floppy
Auto GAP3
Number of track =77 , Sector per track=8
Sector ID start =1 , RPM =360
Sectors size =1024 , Bitrate =500000
Format value =246 , Interleave =1 , Skew =0 Total sector =1232 , Total size 1261568
That's all
Then click tab "Creat Empty Floppy"
Back to windows "HxCFloppyEmulator V1.6.11.15"
Click tab"Export" then export to my sdcard and format again with Japanese dos.
After format can operate on PC 98..xx series but cannot open with vfdwin.
The error occor send Error Report or Don't Send
Re: Cannot write and format in drive B:
Or if you want real image affter format.
Please tell me how to send to you.
Image file size 3158kB.
Please tell me how to send to you.
Image file size 3158kB.
Re: Cannot write and format in drive B:
zip it and send me the image by email.sixty_cel wrote:Or if you want real image affter format.
Please tell me how to send to you.
Image file size 3158kB.
Re: Cannot write and format in drive B:
OK I'm sent image file to your Email.